Microlife A200 Navigationshandbuch PDF herunterladen (Seite 8)

displayed). Although the device will continue to measure reliably, you

should obtain replacement batteries.

Flat battery – replacement

When the batteries are flat, the battery symbol AR will flash as soon

as the device is switched on (flat battery displayed). You cannot

take any further measurements and must replace the batteries.

1. Open the battery compartment AT at the back of the device.

2. Replace the batteries – ensure correct polarity as shown by the

symbols in the compartment.

3. To set date and time, follow the procedure described in

«Section 3.».



The memory retains all values although date and time must

be reset – the year number therefore flashes automatically

after the batteries are replaced.

Which batteries and which procedure?



Use 4 new, long-life 1.5 V, size AA batteries.



Do not use batteries beyond their date of expiry.



Remove batteries if the device is not going to be used for a

prolonged period.

Using rechargeable batteries

You can also operate this device using rechargeable batteries.



Only use «NiMH» type reusable batteries.



Batteries must be removed and recharged when the flat

battery symbol appears. They should not remain inside the

device as they may become damaged (total discharge as a

result of low use of the device, even when switched off).



Always remove the rechargeable batteries if you do not

intend to use the device for a week or more.



Batteries cannot be charged in the blood pressure monitor.

Recharge batteries in an external charger and observe the

information regarding charging, care and durability.

10. Using a Mains Adapter

You can operate this device using the Microlife mains adapter

(DC 6V, 600 mA).



Only use the Microlife mains adapter available as an original

accessory appropriate for your supply voltage.



Ensure that neither the mains adapter nor the cable are

damaged.

1. Plug the adapter cable into the mains adapter socket 8 in the

blood pressure monitor.

2. Plug the adapter plug into the wall socket.

When the mains adapter is connected, no battery current is

consumed.

11. Error Messages

If an error occurs during the measurement, the measurement is

interrupted and an error message, e.g. «ERR 3», is displayed.

* Please consult your doctor, if this or any other problem occurs

repeatedly.

Error Description Potential cause and remedy

«ERR 1» Signal too

weak

The pulse signals on the cuff are too

weak. Re-position the cuff and repeat the

measurement.*

«ERR 2»

Error signal During the measurement, error signals

were detected by the cuff, caused for

instance by movement or muscle

tension. Repeat the measurement,

keeping your arm still.

«ERR 3»

No pressure

in the cuff

An adequate pressure cannot be gener-

ated in the cuff. A leak may have

occurred. Check that the cuff is correctly

connected and is not too loose. Replace

the batteries if necessary. Repeat the

measurement.

«ERR 5» Abnormal

result

The measuring signals are inaccurate

and no result can therefore be displayed.

Read through the checklist for

performing reliable measurements and

then repeat the measurement.*

«ERR 6»AFIB/MAM

Mode

There were too many errors during the

measurement in AFIB/MAM mode,

making it impossible to obtain a final

result. Read through the checklist for

performing reliable measurements and

then repeat the measurement.*

«HI» Pulse or cuff

pressure

too high

The pressure in the cuff is too high (over

300 mmHg) OR the pulse is too high

(over 200 beats per minute). Relax for 5

minutes and repeat the measurement.*

«LO» Pulse too

low

The pulse is too low (less than 40 beats

per minute). Repeat the measurement.*

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Microlife A200 Navigationshandbuch Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Blutdruck-Geräte Microlife A200